NFC Tag Scan Distance Explained


It’s a typical problem. An NFC tag is integrated into a product or behind a piece of advertising material and now the tag can’t be scanned. The reason is simple. The tags scan distance isn’t good enough. So how do you maximise scan distance ?

There’s a number of factors which you need to bear in mind :

NFC Chip

There are significant differences in scan distance performance between NFC chips. The age of the original chip design can often be a factor but the biggest factor is often the technology within a chip. More complex technology such as encryption can require an increase in ‘energy’. Because the tag gets all it’s energy from the proximity of a mobile phone (or other reading device) then an increase in energy requirement typically means the phone needs to be closer. Simpler tags therefore tend to be more energy efficient.

For example, the MIFARE Ultralight C® chip which contains advanced encryption technology can have a scan distance of less than a third of a simpler chip such as an NTAG213.

So, the rule here is simple. If you don’t need advanced tech, don’t use those chips.

Tag Size

Let’s be clear. It’s not so much about the tag size that affects scan distance, it’s about the antenna size. The antenna is the coil of wire within the NFC tag that creates the energy and powers the chip. In theory, the bigger the antenna, the more energy that can be harvested.

In short, a larger antenna can harvest more energy so you can hold the phone further away and thus you have increased scan distance. There are, however, diminishing returns and you rapidly reach a point where two things happen.

First, you have effectively become as efficient as you can be with the power source in question (the phone). This can best be described as you lose more energy in the antenna itself than you gain.

Second, your antenna design becomes mismatched against the design of the reader antenna.

The ability to scan has a direct effect on user experience. The ability to scan comes down to two things. How close a user needs to hold the phone and how accurate placement needs to be. As with web pages where a user can give up on a slow loading page very quickly, a user will give up on a slow responding tag much quicker than you would think.

The rule here is generally use a tag as a large as you can. A 29mm to 38mm tag size is ideal. A credit card size is generally no better than a 38mm for mobile phone use. Tags smaller than 25mm need careful consideration and shouldn’t be used for marketing.

Tag Design

Tag design is a very complex area. Let’s consider just one simple point – antenna design.

Let’s consider that the quality of the antenna design can best be described (in this context) as how much of the available space does the antenna take up. To explain this better, consider that a bigger antenna is generally better.

To define ‘bigger’ you then need to consider the total length of the antenna. So a single strand of wire in a simple loop would be ‘smaller’ than a single strand looped three times. In other words, it’s not all about the extent of the antenna, it’s about the length.

Now most NFC labels are etchings. That means that it’s a single wire in a spiral loop. Clearly, within a 25mm diameter space there’s a limit to how long that wire can be. However, the coil length can be affected by the position of the chip and the thickness of the ‘wire’ (and the gap between the wire). It can make a significant difference to the actual length.

Additionally, particularly with labels, there’s a margin. That’s the gap between the outermost edge of the coil and the edge of the label. So your label might be 29mm but your coil diameter might only be 25mm. This is typically defined but ‘tolerance’. This is the ability of the manufacturer to get that coil in the right position. A cheaper manufacturer will have a poor tolerance and to compensate, a smaller antenna will be used. What you get is a poor performing tag for the size.

The rule here is buy good quality tags and ask what the size of the antenna is rather than the size of the label.

Tag Quality

We could have put this under tag design and there’s large number of factors here as well. Let’s again consider a single point which is frequency tolerance. This might require a little concentration !

Simply put, the tag and the reader communicate at a specific frequency which is 13.56Mhz. Much like with a radio where a small variation in ‘tuning’ can result in a poor sound or distortion, a variation in tag tuning can result in a reduced performance.

In an ideal world, every tag that ran off the production line would have perfect tuning but that’s not the case. In reality, there’s often quite substantial variance. This can be caused by the antenna etching, the bond between the antenna and the chip, the chip itself a number of other factors.

A good manufacturer will be able to control this variance better and importantly, quality control the final output.

The rule here, therefore, is buy good quality tags.

Actual Scan Distance

So, what scan distances can you actually expect in the real world. Well that depends on the phone, the tag and the placement (which can affect the tuning). Even more complicated, it can also depend on the tag/phone combination where one antenna design can work better than another with a particular phone.

Which means that there’s no hard answer. But, as a general rule, a 40mm tag (with 35mm antenna – see above) with an NTAG213 chip paired with a good Android phone should get 7-10cm without too much problem. A tiny NTAG213 tag (12mm x 19mm for example) might achieve 2-3cm.