NTAG213 TT Tag Tamper Features Explained

0
414
NFC Tamper Medicine : Image clickandphoto / 123RF

Early in 2017, NXP launch a variation of their popular NTAG213 chip. The NTAG213 TT ‘Tag Tamper’ chip was designed to detect tampering or modification to packaging. This is how it works.

How tamper tags typically work

Tamper tags or tamperproof tags are not new. In fact they have been quite a few variants but there’s an important difference between this new NTAG213 TT chip and the previous generation of tamper tags.

To understand the difference, it’s important to remember that an NFC antenna is a coil of wire. If that coil of wire is broken then the tag will fail to energise and the tag will not work. The principle therefore of the standard tamper proof tag was simple. Any attempt to remove the tag label should break the antenna and effectively stop the tag from working. There are a number of ways this might happen.

In some cases, the tags material can be very fragile. An attempt to remove it might cause the tag to quite literally fall apart. As a user tries to peel it away from it’s attached surface, the actual material substrate and antenna of the tag will disintegrate and the antenna loop will be broken.

In other cases, there can be a ‘two part’ construction to the antenna. When the tag is removed, one part of the antenna will detach itself from the other part, thus breaking the loop.

This means two things. Firstly, the chip itself is not broken or changed. Simply, the antenna is broken which means that tag not the chip is modified. Secondly, after the tamper, the tag does not function. This might seem fairly obvious but it means that a user trying to scan the tag does not know if the tag has stopped working, never worked, or has been tampered with. It simply does not work.

How the NTAG213 TT works

The NTAG213 TT allows a different design. Instead of a single antenna loop it has an additional two connections allowing for two loops of wire. This second, additional, loop of wire can now act as the one that ‘breaks’ but without damage to the important antenna loop.

This serves two significant benefits.

Firstly, NFC antennas need careful tuning to make sure that they work properly. The length, design and material need to be designed to ensure good performance. This makes the older design of tamper tags more difficult because this tuning has to be taken into account. With the NTAG213 TT, the antenna is independent which means it can be tuned and set like any normal NFC antenna. The tamper loop can now be used in any shape or format that works best.

Secondly, and importantly, the tag will continue to work after the tamper action. This means that it is now possible to scan the tag to detect a tamper rather than the previous action which was just to be presented with a dead tag.

Image of the tamper loop on an NTAG213 TT NFC tag
Image of the tamper loop on an NTAG213 TT NFC tag. Image : Seritag

How the NTAG213 TT presents tamper

Clearly, if the NTAG213 TT simply allowed a scan after tamper it wouldn’t be doing much as a tamper tag. So what actually happens is that the NTAG213 TT can change the content of the data dynamically to indicate that it has been tampered with.

For example, a typical use case might be that the tag is encoded with a web address such as https://t.ixkio.com/t?a=x7k&u=04473D5A5A5780&t=00000000 where the t variable indicates a data code being dynamically set by the chip. The default state would be ‘00000000’. Now, should the additional tamper loop on the tag be broken, the tag can still be scanned but the chip will automatically change the ‘00000000’ to, say ‘FFFFFFFF’. The web address when it is now scanned will show https://t.ixkio.com/t?a=x7k&u=04473D5A5A5780&t=FFFFFFFF, allowing a developer to display a different page and show that the tag has been modified.

It’s a simple solution, but effective.

Tamper Tag Use Cases

Typically, the tags are used the detect the opening of packaging. This can either be in the cap/lid of a bottle so that as it the cap is twisted, the tamper loop is broken. However, tamper tags can also be used for single use ticketing or vouchers.

On-Metal NFC tamper tags

One of the most common use cases for tamper proof tags is for asset management. As many readers of NFC.Today and many NFC users in general will know, NFC tags and metal aren’t the best of friends. Normal NFC tags cannot be used on metal surfaces. To allow an NFC tag to be used on a metal surface, an additional ferrite layer needs to be included between the tag and the adhesive.

Unfortunately, this additional layer creates substantial design issue for both standard tamper tags and the NTAG213 TT tamper tags. NFC.Today have seen a few designs where the tamper loop runs on the metal side of the ferrite layer to the antenna/chip side of the ferrite layer but the cost implications of reliably making such a construction mean that it’s all but a design idea.

In short, NFC.Today have yet to see a suitable on-metal tamper tag in any variant. Tamper tags and metal surfaces don’t mix.